BSC City Names Vote
Added 2017-01-15 21:52:20 +0000 UTC
http://www.clickspringprojects.com/BSC-City-Names-Poll.html
OK, the nominations for the BSC Northern Hemisphere dial cities are now in, so let the voting begin!
Like any good horse race, its a wide open field with a few favourites, and more than a few roughies (hello Walla Walla!). If you're looking for inspiration on how to cast your vote, then look no further than the previous nomination post - some truly excellent suggestions and reasons for inclusion given.
The key piece of data that the cities will convey on the dial is Latitude, but that need not necessarily influence the city selection. It's the place itself that matters the most - Its name, what makes it known to the world, and most importantly what makes it special to you.
I will keep this poll open right up until the day I make the dial. Lobby your fellow Patrons in the comments below, and may the best 16 win!
http://www.clickspringprojects.com/BSC-City-Names-Poll.html
Comments
There is a name I haven't heard in nearly 50 years; my first watch as an 8 year old was a Waltham
Benny
2019-06-11 08:19:55 +0000 UTCAwesome to have you on board Lars!
Clickspring
2017-02-24 20:36:13 +0000 UTCI have made several fly cutters in a similar, although less advanced way. They work very well and in my opinion and the addendum radius is not all that critical. Thank you for the calculator it will speed things up. I think the projekt is very beautiful and I am looking forward to the start. Now you have a patron from Denmark.
Lars U. Lamm
2017-02-24 12:54:13 +0000 UTCJust a thought, something will be really wrong if Byzantium does not make the name cut...
2017-01-28 22:06:25 +0000 UTCSure thing Ed, any time :) Depends how thin the sheet metal is and what its made of - if its much thinner than 0.5mm then it may be worthwhile to consider a punch rather than a broach. The main issue using a broach on thin stock is alignment - there should be at least 2 teeth in contact with the work at all times to maintain alignment. I say *should* because you can still make it work if you're careful, but its not best engineering practice. You can also clamp a guide above the stock if need be, and achieve the same result. As to tooth profile, not sure exactly what you mean by "smooth and flat" - but a broach can be pretty much any shape you want the final hole to be. Hope that helps!
Clickspring
2017-01-28 04:52:12 +0000 UTCMight be a bit of a weird question, and it's not related to the sundial at all, but can I ask about broaches? That square one you made fascinated me. Say you wanted to pierce and widen a hole in a thinner sheet of metal, not a block - would the profile of the broach be any different? Could it be smooth and flat or would it still be stepped?
Ed Arthur
2017-01-27 22:03:18 +0000 UTCNice one Ben, thanks :)
Clickspring
2017-01-21 02:08:28 +0000 UTC
2017-01-19 22:29:24 +0000 UTC
StellarDrift
2017-01-18 06:10:26 +0000 UTC
2017-01-17 18:02:43 +0000 UTC
Clickspring
2017-01-17 06:05:47 +0000 UTCPaul Jenkin
2017-01-17 05:58:08 +0000 UTCClickspring
2017-01-16 21:03:15 +0000 UTCKristian Torgersen
2017-01-16 11:39:13 +0000 UTCPaul Grodt
2017-01-16 04:29:02 +0000 UTCClickspring
2017-01-15 23:37:16 +0000 UTCPeter W. Meek
2017-01-15 23:23:28 +0000 UTCClickspring
2017-01-15 22:01:32 +0000 UTCBpendragon
2017-01-15 21:56:30 +0000 UTC
