Sneak peeks of the workshop interior!
Added 2025-01-15 17:00:08 +0000 UTCFloor down: DPM, Insulation and Plywood.
Windows in and sealed.
Door on!
It's time to order the final floor, plasterboard for the back wall and an absolute tonne of plywood for making some ultimate units!!
Comments
🤣
Richard Payne
2025-01-16 17:25:02 +0000 UTC😂😂 well I do want to first test how much heat all these devices give off as it'd be a waste to install heating if all the heated beds and silicon chips can do the work!! 😂
Hands on Katie
2025-01-16 15:25:09 +0000 UTCOh I've been going back and forth on this between engineered hardwood or some really decent quality LVT. I 'think' I'm going with the latter (fully waterproof and less temperature susceptible) and tougher surface for it!
Hands on Katie
2025-01-16 12:42:33 +0000 UTCYou're totally right Fred - they've agreed to upgrade my house to three phase specifically for this, and I was just sketching out all the plug sockets - LOADS is the short plan!
Hands on Katie
2025-01-16 12:41:12 +0000 UTCOh I'm jealous if they've managed in two days!! I can't see how that's even possible for me with all the various dry times for paints/sealers and so on (let alone the snow, ice and rain!!). I'm onto the easy stuff now though - finishing touches!
Hands on Katie
2025-01-16 12:40:12 +0000 UTCI love that your answer to "how will you heat the room?" Is "frickin' laserbeams!" 🤣
Dermot Canniffe
2025-01-16 08:13:14 +0000 UTCThat's amazing. My next door neighbour got something similar recently - after they'd done the concrete pad it was a two-day installation including mains wiring & roofing... I'm a bit jealous tbh.
Dermot Canniffe
2025-01-16 08:11:30 +0000 UTCI am really impressed with the progress on your shop. I did my shop as two bays of a 5-car garage and I know how much work was involved. Be sure that the electrical for lighting and powering your tools is adequate. Determine what you need and then add about 50% :)
Old Guy Fred
2025-01-15 19:42:43 +0000 UTCNew shop looks amazing! what will you be using for the floor ?
Stanco
2025-01-15 18:33:12 +0000 UTCAnd filament driers! 🤣
Richard Payne
2025-01-15 17:57:21 +0000 UTCIsn't your other outbuilding a sauna?
Bazza McSpleen
2025-01-15 17:40:23 +0000 UTCHeating - mainly 3d printers, lasers and soldering irons..... 😂😂
Hands on Katie
2025-01-15 17:39:41 +0000 UTCYes, doing the final floor this week and then it's cabinet/work table time!
Hands on Katie
2025-01-15 17:39:12 +0000 UTCInsulation on roof and floor. Walls are 70mm timber, so going to leave for now and see how it goes (can add later if needed, but my other outbuilding annoys me more because it's too hot than too cold!!)
Hands on Katie
2025-01-15 17:38:45 +0000 UTCLooks great! Is the insulation going on the walls, floor, roof, or "yes"? :)
Bazza McSpleen
2025-01-15 17:12:45 +0000 UTCLooking good! Obviously some substantial progress has been made. What are you going to use for heating?
Richard Payne
2025-01-15 17:05:19 +0000 UTC
