Dual Direct drive - Taichi OR cheap dual color hotend
Included in rev29 of the new Apollo zip here
Stock backplate an...
squirrelf3d posts
Speedster (v6+Orbiter2/sherpa+CRtouch+dual 5015) + ender on wheels
Codename "SPEEDSTER"
STL + STEP in the zip
By request, this is built around the Klemco v6 groove mount (get it on 2022-12-18 23:27:27 +0000 UTC
View Post
Apollo-ish with dual 4010
----
edit: files posted : https://www.patreon.com/posts/apollo-mini-dual-79220716<...
2022-12-12 02:57:05 +0000 UTC View PostReplacement cover & mount for BIGTREETECH Smart Filament Sensor
After two fail print (was playing with very low filament flow for support, didn't work, but also means it was printing in mid air for hours), so was great motivation to get that setup.
This ...
LXG lite support - Saturn/Apollo
Here is a printed mount that's easy to install and remove.
uses two M3x8 screws to mount into the Saturn/Apollo Backplate using the sherpa mini model
Apollo on Rail + chain + Orbiter 2.0 + BTT/Mellow FLYSHT36 CAN setup
Tweaked the attached two files to accommodate
Apollo on Rails
+Mellow FLY SHT 36 (Very likely the BTT model as well, but haven't actually checked)...
Ender6 - Apollo - Dragon ST/HF
This is very experimental, so be ready to come across issues. (which we can then fix)
There are cutouts for belts, and for the X endstop.
The backplate is standard Apollo (so if you w...
Tiny underside cap
Have you ever cut your finger, or splice some wire there, well I come to the rescue! (ok neither of which happened to me, but always kinda bothered me how sharp it was)
Well not much else ab...
Open Air case for E3 boards + IDEX board + 80mm fan
The mount was meant for BTT E3RRF + IDEX
BTT E3RRF board has the same mounting point as any E3 board format (stock creality and all E3 iteration for BTT and oth...
48mm motor on Y
-----
Rev2: 4248_rev2.1.zip
- another minor tweak on the motor mount ... 2022-10-09 16:24:29 +0000 UTC View Post
Cable Chain for the Apollo on Rails
-----------
revised model : https://www.patreon....
Projects
-----------------------------------------------------------------
-----------------------------------------------------------------
-----------------------------------------------------------...
ApolloLander - stock plate and linear rails
----
Hot threaded insert
m3 x 4mm Length x 5mm Diameter - https://amzn.to/3Z1Rwej
Or
m3 x 4m...
2022-08-27 00:19:13 +0000 UTC View PostDropEffect eXtreme Gradient hotend - rail mount (MGN12h) - ender3/pro/v2
-----
Oct 21: added a belt mount with wider slots
-----
STEP file included
Screw length (might be some small mistake, but should mostly correct)
- 4x M3x... 2022-08-24 21:03:36 +0000 UTC View Post
DropEffect eXtreme Gradient - simple mini setup - on wheels
2x M2x12 (bottom fan screws)
2x M2x8 (top fan screws)
2x M3x6 - flat head - accessories screws included with the hotend
2x M3x25 - hotend mount
Hotend itself STEP f...
X endstop for front facing linear rail setups
Also added a bunch of additional mounting point for accessories and such because why not! never know when these can come in handy.
Besides the 4 stock motor mounting screw holes, t...
2022-08-16 03:13:54 +0000 UTC View PostADXL345 (generic) Y axis potential solution
Just an idea, open to any suggestions.
Secure the adxl to this with M3x4 screws, place the screws and put a little pressure as you screw in until the screw grabs the plastic, then you'll be ...
Y dual linear rail mount - ender3pro/v2/Max - MGN12H
Update: installed on my machine and it works great!
(I uploaded new alignment tools as the top mounted rail model were too long for this.)
Stock Y endstop switch can stay in place...
2022-07-18 18:25:51 +0000 UTC View PostFront mounted X linear rail setup - ender3/pro/v2/max/S1
-----
May 31:
small update (no need to reprint if you did) - backplate_1of2.stl had mesh errors which usually the slicer can fix without issues, but fixed it anyway,...
Going away for most of June - but I'll be back!
Hi all, first of all I want to thank every single one of you for supporting my work! It means a lot, and appreciate it so much!!!
I will be away for most of June (visiting family followed by...
Direct Drive filament bowden guide - for ender3 stock extruder platform
Made to use with those little pneumatic fitting (aka bowden collet) as pictured
2022-05-28 05:05:44 +0000 UTC View PostSmall box for bolts, nuts, etc... (STL/STEP)
I needed something asap, so it's nothing fancy, and not extensively tested.
Not sure if there is any interest for this, but decided to post it anyway.
my only requirements were that it sna...
2022-05-15 17:49:22 +0000 UTC View PostFront mounted bltouch/crtouch + STEP
Updated bltouch model Aug15 2022
----
By request, here is a front mounted bltouch
use screws (M3x8) and M3 nuts to secure the bltouch and longer...
Ender 3v2/pro - Y - single linear rail (MGN12H)
-----
June 3
Added STEP file for ender3/pro/v2, with two sizes, shorter one for use with longer than stock replacement belts and longer one to use the stock belt. ...
X axis linear rail adapter plate ender3/pro/v2/max (MGN12H & MGN9H)
I don't recommend using this with the Apollo, as the Apollo has direct mount to front mounted rail (unlike the Saturn)
For a top mounted rail the Apollo support the wambam plate...
Just a bunch of Klipper related resource & info
This will keep being updated. Mostly links.
If you find anything interesting feel free to post in the comment below.
To locate Raspberry Pi in stock: 2022-04-12 18:04:29 +0000 UTC View Post
E motor (42-40) on Y axis (ender3v2, maybe pro?) STL+STEP
Might work on other printers, not sure of their setup
The Stock extruder motor (42-40) has a bit more torque than the Y stock (42-32) so if you ever experienced Y skips this will hel...
Klipper - screws_tilt_adjust - Leveling your bed
klipper will work on all board, even stock, you just need a Raspberry Pi or Orange Pi or similar and connected via USB or via 3 GPIO pins (using UART)
WHAT...
2022-04-06 19:27:19 +0000 UTC View PostSaturn - Ender 6 - (Dragonfly BMS / Dragon / Rapido)
If you want to test another hotend with your ender6 let me know.
Right duct confirmed working! Thanks to Merkaba for all the testing!!!
Body is good too
---
Larger (40mm Diameter) X/Y tension wheel - ender3v2
Those stock tension wheels can be annoyingly small (approximately 18mm diameter), so here is a larger variant that will still fit under the moving bed on a ender3v2
You can either use a