REPOST: Get Sharp with Sandpaper
Added 2020-03-03 12:31:56 +0000 UTCFriends:
The original version of this video had about 20 seconds missing from the end. I needed to delete the old video to upload the fixed copy, so here's the fixed version. There's nothing new to see; I just wanted the video to be up. The old post is about to be deleted.
Sorry to clog up your email!
--Rex
Comments
Thanks Rex, it's a pleasure to be here.
John Gray
2020-04-15 20:21:58 +0000 UTCDon't feel guilty! I'm happy just to have viewers...but I'm even happier that you've joined our little community. Get back into the craft! It's not that hard.
Rex Krueger
2020-04-15 17:27:25 +0000 UTCHi Rex, I am a new patron from the UK and thought I'd let you know I've been watching all your YouTube videos and felt guilty that I wasn't supporting you properly. I am in my 50's and have not done woodworking since school at 12yrs old. These newbie videos are very useful. Thanks so much for reminding me that I really liked working with wood as a boy and it's never too late.
John Gray
2020-04-15 10:31:00 +0000 UTCthank you this has answered alot for as i am new to hand planes
Steve Parry
2020-03-18 21:11:32 +0000 UTCA picture would be helpful, but yes, a curved iron is normal for a jack. It's a rough plane, much like a scrub.
Rex Krueger
2020-03-13 14:42:35 +0000 UTCI'm restoring a Butchers jack plane, and have started on the iron - but the bevel is curved instead of flat. Is that normal? Or is it perhaps from a previous owner? Just wondering, before I hit it with the grinder.
Howard Tuckey
2020-03-13 13:39:42 +0000 UTCAwesome thank you for the reply! So even though I have a #5, still set up the #4 as a scrub? Sorry dont mean to be a bother, just want to do it right...
Josiah Peters
2020-03-09 11:45:46 +0000 UTCI get it. For the Joiner's bench, set it up as a scrub. That's all I needed until i flattened the top and even then, I did 90% of it with a scrub.
Rex Krueger
2020-03-09 10:35:34 +0000 UTCOh sure! You can do the outside of the gouge on the sandpaper like normal. The the inner curve, plane a piece of wood to a matching radius and put sandpaper over that. Easy.
Rex Krueger
2020-03-09 10:33:39 +0000 UTCRex, is there a good way to use sandpaper or stones to sharpen for gauges? I just came into a couple of beat up ones that I'm going to clean up with a wire wheel, but im not sure how to get a sharp edge on the curve (probably not a job for the honing guide) Could this be something to teach Nate in the oil stone/hand sharpening video if it's only a small adjustment from hand sharpening?
Michael Motley
2020-03-07 16:44:09 +0000 UTCHey Rex, I got a question. I'm gearing up for woodworking and I'm restoring my first plane. It's an old craftsman, number 4 look alike. The tote was split so I got it fairly cheap and I figured itd be good practice before I restored the Stanley #5 that a friend gave me. My question here is, in gearing up to start building the jointers bench and such, what configuration should I set up the iron for? I have the one iron for it and have no problem using it as a beater, but I'm not sure if it should be a smoother, or a scrub, ooor..
Josiah Peters
2020-03-07 15:33:14 +0000 UTCI'm sure it will come out great!
Rex Krueger
2020-03-07 13:50:18 +0000 UTCJust wanted to thank you for the great video and tell that you inspired me to begin woodworking! I'll be doing myself a Roman low bench pretty soon!
Thiago Queiróz Ruiz
2020-03-06 21:56:59 +0000 UTC25 is a good angle, but don't sweat it. Anything around there is good. I go for 30ish. The edge is stronger.
Rex Krueger
2020-03-06 11:53:46 +0000 UTCI'm really glad it's working. These True Beginner Videos don't get a ton of views, so it helps to hear people are getting a lot out of them.
Rex Krueger
2020-03-06 11:50:47 +0000 UTCIf I knew a lady who was interested, she would be in my shop RIGHT NOW.
Rex Krueger
2020-03-06 11:50:04 +0000 UTCWe're delighted to have you! I do think diamond stones are probably the best, but they are pricey. When I find cheap ones that last, I'll make the switch.
Rex Krueger
2020-03-06 11:49:29 +0000 UTCDMT and Eze-lap are good brands
Paul O'Hanlon
2020-03-05 21:59:35 +0000 UTCI would recommend the Trend 300/1000 diamond stone, two grits in one. Whatever brand you go with, look for monocrystaline type.
Paul O'Hanlon
2020-03-05 21:59:14 +0000 UTCI know you prefer oil stones, do you have an opinion on Diamond Stones? I tried looking online if you've made a video or written a post. I did find a 2018 article where you talk about the pros and cons of different stones or machines but nothing on Diamond Stones. From reading online people recommend DMT due to their quality. I've read on forms and other review sites that a Diamond stone, mainly DMT, will out last any stone, will never need to be flattened, and like other stones comes double sided. Looking at your videos on stones and even the cheaper options can last a while which is nice. Is the added bonus of never needing to flatten a diamond stone worth investing or am I just being roped in by a nice looking piece of metal with glued diamonds? PS I have been watching you, and a couple of other woodworking enthusiasts for a few months. I have to say the amount you offer your patreon was so low I had to join today! Anyways I've really appreciated the work you and Nate put in, I've slowly managed to build a semi decent garage shop with your advice!
G Wing
2020-03-05 00:08:02 +0000 UTCNothing against Nate, but it doesn't have to be just him, either. A female beginner would be a not bad idea either. These "beginners" are stand-ins for us, your viewers.
Paul Thoma
2020-03-04 21:42:52 +0000 UTCAnother great video. I watch these each several times, then try the techniques myself out in my shop. They are completely changing how I see woodworking. Also: your great series is getting some well-earned attention https://www.reviewgeek.com/35316/4-youtubers-you-can-learn-woodworking-from/
Paul Thoma
2020-03-04 21:38:43 +0000 UTCTo practice my honing skills,when I bought my bit brace, paid a dollar for a rusted chisel. I got all the rust off with regular white vinegar. I’m now honing it on 400 grit wet/sand paper, just as you did in your video. I have 800 grit too. I will then use a 1000, 4000, 8000. Not sure of an angle...so, I used a 25 degree angle, which matched a new chisel that I bought from the store.
Marc Gigliello
2020-03-04 18:51:36 +0000 UTCI'm really glad you think so!
Rex Krueger
2020-03-04 18:14:56 +0000 UTCI honestly learn a lot watching him learn. The kid is no dummy, so when he doesn't get something, I know it's not HIS fault.
Rex Krueger
2020-03-04 18:12:57 +0000 UTCThank you!
Rex Krueger
2020-03-04 18:10:43 +0000 UTCAwesome video. The tight focus on the sharpening/honing process is great for anyone needing to tune up a plane. A great video to share.
Michael Nix
2020-03-04 13:19:26 +0000 UTCBringing in Nate is the best thing you can do to teach a technique over a video. You never know know what problem a new user will run into. It's like knowing how everything works in a house, but not having the key to the front door. Keeping your hands off the tool he is using is very important.
ian Webster
2020-03-03 17:02:56 +0000 UTCAs a plumber, that is the only clog I dont mind. Thanks for the great content. Bringing in Nate is a great addition.
Mike Willey
2020-03-03 13:44:04 +0000 UTC
