All the hardware is modeled in the step file, you'll need some M3 heat set inserts, 5mm dowel, and 8mm flat head and cap head m3 fastners. MGN12 200mm with an H block.
Current build is using...
Hey y'all, I'm planning on being a bit more active here in the future, yay!
Here's two parts I threw together and remixed with Tempest's originals to address some early needs I've seen peopl...
This is the first version of this idea I'm happy enough with to release, even though there are still a few changes to make. I'm putting this in a few private places because I'm not sure if there's ...
2022-07-23 03:01:53 +0000 UTC View Post
It's now assembled, I don't have a full connector solution yet other than soldering and crimping, but it's not difficult stuff.
Picture 1 is the lube attachment, the tubing bends inwards and ...
2022-06-22 09:07:48 +0000 UTC View Post
I'm pretty happy with this version. The lube path is fully silicone/ptfe, tip pops into the end of the fleshlight and moves with it. Wiring is run all the way up to the top and is intended to outpu...
2022-06-21 05:57:58 +0000 UTC View Post
Been a bit too long since I posted here, but I've been getting into batteries and portable devices recently and here's what I'm bringing back from the exploration.
This is intended to be ...
2022-05-19 00:13:48 +0000 UTC View Post
Pretty happy with this case. Even though I need to widen the wiring channels a bit it feels super solid. I mounted the 3 vibration motors separately from the heaters so they would not contact...
2022-04-21 05:34:00 +0000 UTC View Post
Tabs rolled over too much to stay retained. I could have put a screw through the twist ring into the case, but eh....
Anyway, it's got a built in axial twist servo, heater compartments, and ...
Sorry about the bad image quality, didn't realize my lens was dirty.
I'll probably reduce the amount of fasteners this angle bracket uses as it's extremely rigid as is. This allows for ...
2022-03-16 12:40:16 +0000 UTC View Post
This is the fourth version of extrusion arrangements I've tried for this mount and it's the first one I'm happy about, so it's what I'm going to attempt to release a easy to build at home version o...
2022-03-13 07:32:52 +0000 UTC View Post
This sits on top of your ESP32 and distributes your robot's power without soldering. Simply strip and tightly twist your leads together, and insert them into the lever nut, making sure to give each...
2022-01-23 21:55:21 +0000 UTC View Post
NOTE: If you are using JX servos, please get the JX versions below, they have slightly different mount patterns than most servos, which is enough to cause some alignment issues with M4 bolts. Thank...
2022-01-16 23:43:19 +0000 UTC View Post
The attached videos are little teasers I've posted on Tempest's discord, but I think I'm going to end up making one with actual hardware to it so I can mount accessories and batteries to it. <...
2022-01-04 12:00:57 +0000 UTC View Post
Putting this here so I can update it as needed, if you've got input feel free to share. ESP32s are easy to use, but getting over that first learning curve is easier with an image.
2021-12-19 00:05:42 +0000 UTC View Post
This uses a small 4010 fan to blow air (mostly) out of the servo gaps, via an air intake. You can stuff a little crumpled up scrap of paper in the gaps of the micro usb port then fully tighten down...
2021-12-12 14:51:18 +0000 UTC View Post
These are almost identical to the stock SR6 Beta 1 arms with the following differences:
Servo horn screw access
Slightly tighter tolerances (0.2mm on each side) at the end of the horn, ...
2021-11-08 14:26:33 +0000 UTC View Post
NOTE: I've updated this pack to contain both stock thickness arms and arms that are reduced by 0.5mm (some servo splines are a little farther out and this can cause the pitch arms to rub together m...
2021-11-01 10:54:44 +0000 UTC View Post
I don't have the full BOM for this yet, as I'm testing some lower weight components, but regardless of how you put rod ends on your arms, this should help make sure you have the spacing correct for...
2021-10-31 03:26:19 +0000 UTC View PostQuick update: Voron is done, it rules, and I'm actively developing mods again. I've back burnered the SR2 quiet case because I don't have a great idea of how I want to finish it off. I'm sure I'll ...
2021-10-31 03:22:32 +0000 UTC View Post
Probably about two weeks from being able to print things larger than 80mm reliably, yay!
2021-10-18 05:39:09 +0000 UTC View Post
I'm about 8 hours into building it over the past two days, I'm going slow to make sure I don't get stuck with big rebuild later. I've also possibly been converted to using heat set inserts again, t...
2021-10-12 00:31:51 +0000 UTC View Post
Update: The V2 stl below fits Lumifel's single print receiver and has mount holes for further modding.
This dampens the sharp gear noise that comes off the Parallax servo, but does...
2021-10-09 17:16:02 +0000 UTC View Post
NOTE: Print the spacer to bring your A11CLS back to parallel, this servo's spline is 2.55mm below the stock SG90 spline.
Quick little part mod as I get my workshop redone, if you've got an A...
Waaaay earlier than expected. I'll post progress pics!
2021-09-24 03:50:58 +0000 UTC View Post
How's that for a part name? It's a drop in replacement for the T-Valve Blades part, and it looks like a scorpion, so... I guess that's what it's called.
Includes built in supports, just open ...
2021-09-23 10:46:04 +0000 UTC View PostPrinter's dying, so I'm printing parts for a Voron 2.4 before I resume dev on my case. About 80% done thankfully!
2021-09-09 06:27:30 +0000 UTC View Post
I've had to go back to redesign some parts with my quieter SR2 case, the assembly was just a bit too complex so I'm simplifying. Until then, here's some screen lids for your current SR6. The SR6 be...
2021-08-25 03:27:02 +0000 UTC View Post
This is where I'm at with the quiet case, by the way. Red parts are servo mounts and front covers, green part is where the controllers, power, and fan stuff goes.
Yellow is something that is ...
2021-08-13 18:49:27 +0000 UTC View Post
NOTE: There is a good chance we will see the SR6 Beta soon, and these parts are not going to be compatible as they require my Nutted SR6 Base part, which I've included in the zip....
2021-08-04 05:52:27 +0000 UTC View Post
The part on the outside of the servo is custom fit to this model servo, but it's also an optional part and should fit a lot of other servos that have the same "face" shape.
Heat sinks are 15...